System Futaba

System Futaba

Frit compression

Background

Traditional methods of buckypaper production involves the use of surfactants to disperse carbon nanotubes into aqueous solutions . It was found that filtering this suspension allowed the nanotubes to pack together in a paper-like mat, thus coining the term uckypaper (bucky being the reference to the buckminsterfullerene molecule). The problem was the difficulty in removing the surfactant afterwards, where the surfactant has been linked with cell lysis and tissue inflammation .

Acid oxidation of carbon nanotubes can also be used in filtration to form buckypaper, but requires a high degree of surface acidic groups in order to obtain efficient dispersal in aqueous solution.

Synthesis

A frit compression system for casting buckypaper

An alternative casting method was developed in 2008 to produce buckypaper that did not require the use of surfactants or the acid oxidation of carbon nanotubes in order to obtain high-purity buckypaper for biomedical applications.

The frit-compression system was adapted from a Solid phase extraction (SPE) column, where a suspension of carbon nanotubes is squeezed between two polypropylene frits (70 micrometre pore diameter) inside a syringe column. The pore structure of the frit allows a rapid exit of the solvent leaving the carbon nanotubes to be pressed together. The presence of the solvent controls the interaction between the tubes allowing the formation of tube-tube junctions; its surface tension directly affects the overlap of adjoining nanotubes thus gaining control over the porosity and pore diameter distribution of buckypaper. The distribution of carbon nanotubes in solvent does not have to be a stable suspension, rather a general dispersion serves much easier to keep the nanotubes between the frits rather than pass through them.

Once the system is compressed, the frit-carbon nanotube sandwich is removed from the syringe housing and allowed to dry. The frits can then be removed to leave intact buckypaper. This methodology rapidly speeds up the casting process, avoids use of surfactants and acid oxidation, and the solvent can be fully recovered.

Variety

Buckypaper from frit compression of multi-walled carbon nanotubes

A water-cast buckydisc with convex lower surface

Buckycolumn just after casting

Buckycolumn with hyperboloid geometry on drying

Buckyprism with casting frit

The cross-sectional geometry of the syringe housing will determine the final structure of the buckypaper and the amount of carbon nanotubes added to the column will affect the height of the carbon nanotube mat. Although there is currently no formal classification for paper, discs and columns, it was deemed necessary to differentiate between the different structures obtained for research purposes.

Buckypaper

Typically, cylindrical columns are used with a few milligrams of carbon nanotubes in a solvent. This generates buckypaper with a circular cross-section and film heights of a few hundred micrometres. Buckypaper is usually a class of carbon nanotube mats with depths from 1 to 500 micrometres.

Buckydiscs

For buckypaper with heights larger than 500 micrometres are termed buckydiscs, being thicker than buckypaper and not paper-like. Moreover, when casting in water (72.80 mN m-1), the edges of the film can lift due to surface tension effects of the remaining solvent in the system that can pull carbon nanotubes closer together.

Buckycolumns

Buckydiscs with heights larger than 1 mm can be referred to as buckcolumns. These carbon nanotube monoliths often exhibit hyperboloid geometries and are highly compressible

Buckyprism

It is possible to use square housing to generate square cross sections, known as buckyprisms.

References

^ Rinzler, A.G.; Liu, J.; Dai, H.; Nikolaev, P.; Huffman, C.B.; Rodrguez-Macas, F.J.; Boul, P.J.; Lu, A.H. et al. (1998). "Large-scale purification of single-wall carbon nanotubes: process, product, and characterization". Applied Physics a Materials Science & Processing 67: 29. doi:10.1007/s003390050734. 

^ Sun, J (2003). "Development of a dispersion process for carbon nanotubes in ceramic matrix by heterocoagulation". Carbon 41: 1063. doi:10.1016/S0008-6223(02)00441-4. 

^ Ausman, Kevin D; Piner, Richard; Lourie, Oleg; Ruoff, Rodney S.; Korobov, Mikhail (2000). "Organic Solvent Dispersions of Single-Walled Carbon Nanotubes: Toward Solutions of Pristine Nanotubes". The Journal of Physical Chemistry B 104: 8911. doi:10.1021/jp002555m. 

^ Cornett, Jb; Shockman, Gd (1978). "Cellular lysis of Streptococcus faecalis induced with triton X-100" (Free full text). Journal of bacteriology 135 (1): 15360. PMID 97265. PMC 224794. http://www.pubmedcentral.nih.gov/articlerender.fcgi?tool=pubmed&pubmedid=97265. 

^ Esumi, K (1996). "Chemical treatment of carbon nanotubes". Carbon 34: 279. doi:10.1016/0008-6223(96)83349-5. 

^ Leng T, Huie P, Bilbao KV, Blumenkranz MS, Loftus DJ, Fishman HA. (2003). "Carbon nanotube bucky paper as an artificial support membrane and Bruch's membrane patch in subretinal RPE and IPE transplantation". Invest Ophth Vis Sci 44 (5): 481. http://abstracts.iovs.org/cgi/content/abstract/44/5/481. 

^ Whitby, RLD; Fukuda, T; Maekawa, T; James, SL; Mikhalovsky, SV (2008). "Geometric control and tuneable pore size distribution of buckypaper and buckydiscs". Carbon 46: 949. doi:10.1016/j.carbon.2008.02.028. 

^ Futaba, Dn; Hata, K; Yamada, T; Hiraoka, T; Hayamizu, Y; Kakudate, Y; Tanaike, O; Hatori, H; Yumura, M; Iijima, S (2006). "Shape-engineerable and highly densely packed single-walled carbon nanotubes and their application as super-capacitor electrodes". Nature materials 5 (12): 98794. doi:10.1038/nmat1782. PMID 17128258. 

^ Whitby, RLD; Mikhalovsky, SV; Gun'ko VM (2010). "Mechanical performance of highly compressible multi-walled carbon nanotube columns with hyperboloid geometries". Carbon 48 (1): 145152. doi:10.1016/j.carbon.2009.08.042. 

See also

Buckypaper

Nanotechnology

Carbon nanotube

Graphene Oxide Paper

Categories: Carbon nanotubes | Molecular electronics
About the Author

I am China Manufacturers writer, reports some information about led scrolling message , automatic optical inspection.

Radio Control: Futaba 6EX 2.4GHz, 6 Channel Radio Control System Intro by RobotShop.com