Steer Knuckle
 |
 HoBao 87032 Alum Steer Knuckle For Hyper 7 $10.00 Time Remaining: 12d 9h 59m Buy It Now for only: $10.00 |
 CKRC BTA kit B w High Steer Knuckles Axial AX10 SCX10 Rock Crawler $48.95 Time Remaining: 14h 49m Buy It Now for only: $48.95 |
Steer Knuckle
Car suspension types
Believe it or not, the first suspension designs for automobiles were inspired by the horse-drawn carriages which preceded the first automobiles. These were basically beam axles, where a solid beam was attached via leaf springs to the vehicle chassis and the wheels were attached to the ends of the beams. Although solid beam axles worked well enough and are in fact still in use today in commercial and heavy-duty vehicles, ride quality requirements compelled car designers to look into suspension designs that provided improved ride and handling qualities. This is the era where designers used swing axles and trailing arm suspensions in an attempt to give cars improved bump, steering and handling qualities. The Corvair is an example of a car that used swing axle suspension, while the VW Beetle was designed to use a trailing arm suspension.
One of the most significant suspension designs that were developed is the MacPherson strut, which was first used by Ford in the 1950s. It is very popular with manufacturers of mass-produced cars because of its simplicity and compactness. This simplicity also makes the MacPherson strut cheap to manufacture, and its compact design allows a drive axle to pass through the steering knuckle that the strut attaches to. It became a de facto standard for front wheel drive cars in the 70s and is still widely used today. Despite its advantages of being cheap to manufacture and compactness, the MacPherson strut was not well-suited to high-performance cars. Suspension engineers looking for better control and handling developed the double A-arm, or dual wishbone, suspension, which allows a vehicle to generate maximum cornering force.
Up to today, the solid axle is used in the rear for very powerful cars. As with front suspensions, leaf springs were used for rear suspensions, and some mass-production cars used this rear layout until the early 80s. However, leaf springs have fallen out of favour and have been replaced by coil springs or struts. Locating the solid rear axle is accomplished by trailing links and lateral control rods that control the movement of the axle during acceleration and braking. There are other layouts for locating and controlling the so called live axle, but the 4-link is the most common and popular layout in use for cars still using a solid rear axle. However, very few, if any, of today's cars use a solid axle for the rear. Independent rear suspensions are commonplace nowadays, whether a car is front wheel drive, rear wheel drive or all wheel drive. Front wheel drive cars usually employ a variation of their front suspension, modified for use in the back end of the car. Generally, these are either a McPherson style suspension or an A-arm setup. Rear wheel drive cars, on the other hand, normally use different front and rear suspensions. What is prevalent is the use of multi-link rear suspensions to provide a very comfortable ride without degrading handling quality. With all-wheel drive cars, the prevalent suspensions in use are the McPherson strut or unequal length double A-arm. All-wheel drive cars are generally higher-performance cars and their suspension tuning is favoured toward handling over ride quality.
About the Author
Find out more about suspensions or visit this site for spare parts.
can you rebuild a steering knuckle on a 1995 jeep?
Leaking like crazy from the bottom
Where is it leaking from? There is no steering fluid in the knuckles...they are basically heavy duty brackets. If you are leaking a fluid, it is likely one of the following:
A) Brake Fluid (pretty unlikely)
B) Fluid that is dripping from something above and running down the knuckle.
C) Gear oil leaking out of a bad axle seal
Smear a bit of the fluid on your finger. What does it smell like? If its really putrid, its gear oil. That means your seal is bad and the oil from the pumpkin is leaking out. The axle on your jeep has gear oil in it...that oil sits mostly in the pumpkin to lubricate the differential gears. However, some oil travels down the axle tubes to the bearings on the shafts near the wheel. That oil is kept in the tube with a seal. The seals go bad after a few years and need to be replaced.
Not hard to do...get yourself a Hayes manual from the local auto parts store and it will walk you through it.
F3141 Universal Steering Knuckle Spreader Toolset - Ball Joint Install Video
You can follow any responses to this entry through the RSS 2.0 feed. Both comments and pings are currently closed.
Comments are closed.