Nitro Petrol

Nitro Petrol

Nitro RC Cars " How To guide "

Nitro rc cars are becoming very popular now and is a fun hobby. With nitro cars there is a little more extra work to do than electric rc cars, but the speed nitro brings is awesome.

Below is a general round up on questions and answers on getting a nitro rc car and how to start them.

Q. What age are nitro radio controlled cars recommended for?
A.  14+ is best. But any younger than 14 you should be prepared to help them with the maintenance, and handle the fuel Nitro RC cars can be a great educational toy and introduction to engineering.

Q. What is the radio range?
A. About 100m but it's always best to do a range check before use, or you could lose control of the vehicle

Q. How do I stop the engine on a nitro car ?
A. Just Cover the exhaust hole with finger or a cloth for a second or 2 and it will turn off.

Q. What kind of fuel do I use?
A. Fuel used is sold from model shops or online. Always use a good branded nitro fuel with a 10-30% content for normal usage.

Q. What speed do nitro RC cars do?   

A. Nitro models can hit 60- 70 mph.       

This is a serious hobby which brings great rewards so read on for information on all areas of buying and starting nitro RC s and more.                                                                                                                                                                                              

 

 

 How To Run In Your Nitro Model

 

The engine needs to be Run-in before full-time use. It is very important that this procedure is carried out. Not doing so will shorten the life of the engine and can ruin it.

There are two different methods you can do to run the nitro engine in. The first way is easier and is also safer as you be less likely to burn the clutch out. I find this way best or with the second method it is more complicated but if done correctly will give a little more life to your nitro engine.

To run your car in, take your finished model and roll it back and forth to be certain the nitro car wheels can turn freely. Then Place the car in a position so that the wheels are off the ground, like on a brick and start the car up and leave to run idle though 3 tanks of fuel make sure between each tank you leave the engine to cool down for about 10 minutes. It is very important to not rev the engine at all as you will badly damage it and also you will break the conrods.

By doing this and taking the time to run your nitro RC car in properly you will have no problems.

The engine should be broken-in on a smooth hard surface. Try to avoid breaking-in the engine on very hot or humid days. Ensure that the idle speed is not too high or else you will burn your clutch out or snap the con rod, and also make sure that the brake is not applied.

Always break-in your engine without the body on the car, you want as much airflow as you can get to keep the engine cool. Do not run the engine too lean or you will over heat it and cause permanent damage to the internal components of the nitro engine.

It is normal for the engine to use a lot of fuel during the break-in. This is because you are running it "richer" than you normally would to keep the engine cool and to flush out the engine as the parts "seat" themselves. Because of the richer than normal setting the performance of the engine will be limited. After break-in, you will then lean it out to gain performance back..

Method 1:

Once it starts and is idling slowly place it on the ground and drive it slowly on a flat surface. For the first use do not let the engine run for more than 3 minutes. Carry on running slowly for short periods until you have gone through 2 - 3 tanks of fuel.

 

 

Do not over accelerate at all during this procedure, as it will severely damage the engine. After each idling time, let the nitro rc car rest for about 10 minutes between each tank. Running in makes sure that the engine is operating correctly before you take it out for a proper run. It is best not to run though any puddles or water as this could burn out the electrics but you can always tape up wires, use silicone on gaps and around the electric box and make sure the screws are all tight before and after each run as these can work loose and you could lose parts while running your car around a park or track.

Always empty the fuel after using as condensation can build up in the engine and damage it if left for a long time and always clean the wheels and ball joints and generally all over as a lot of dirt, sand or mud can build up. This does not take long and keeping the car clean and maintaining it will keep it running good and no money to keep buying spare parts, so it makes sense and also using normal batteries in the controller will run down pretty quick and once the batteries go to under 9V s you could lose control of car if using or worse crash it. Trust me get good rechargeable batteries and then you will always know you have a full charge and you will also save a lot of money in the long run.

Now you know how to break in a nitro RC car but one other thing is that the car will act strange and not run properly while you are using. Don't panic this is normal and it will stall a lot, but this happens to every new car just keep with it and slightly adjust the tuning screw and it will become smooth and an easy ride. This is called "engine break-in" just like when you buy a real brand new car with no mileage on.

 After a couple of tanks of fuel your patience will pay off with a strong, reliable running engine.

If you own a RC Nitro car then regular maintenance is a must..

1. Perform a visual inspection on your rc car -

Check there is no cracks in body or damage anywhere.

Tires are good check rims are still glued well.

2. Wipe down rc car with paper towels or cloth all over

and you can use a small toothbrush to get to awkward parts to clean.

3. Clean air filter with soapy water and rc air filter oil.

These can get real dirty an mud, debris can clog the filter up. You're need

to wash all the parts and dry so make sure to be careful when taking the filter apart.

4. Draining the nitro fuel tank.

If you will not be using your rc nitro car for a while. it is always best to

Drain the nitro fuel out as condensation can build up and this water will mix with

The nitro fuel and seriously damage the engine.

5. Charge up batteries and check over the receiver control is ok.

Doing the above will save you time and money and should take no

Longer than around 40 - 60 minutes.

Get quality nitro rc cars, nitro rc buggys, petrol rc cars and rc tanks. from our great site

http://www.coolnitrocars.com

 

 

About the Author

See our awesome nitro rc cars,nitro buggys and rc jets at low prices and all have Free uk delivery.We also have rc helicopters, petrol rc buggies and rc tanks.

http://www.coolnitrocars.com

 

nitro rc car how do i know what fuel it takes please help?

its a small racing one not sure how big the engine is neither does the person who i bought it off. no box can i use dot 4 oil and petrol mix. or is there a universal fuel.

find a hobby shop around you, they can look at it and see what fuel u can use. no one will be able to figure it out on here cuz u have no info on the thing.

Petrol Nitro RC Cars Ohio